CLI Referenca

Sučelje naredbenog retka OrniFlight (CLI) pruža potpuni pristup svim postavkama. Pristup preko kartice CLI u konfiguratoru OrniFlight, ili preko serijskog terminala na 115200 bauda.

Osnovne naredbe

Naredba	Opis
`help`	Prikaži sve naredbe
`status`	Prikaži status sustava
`version`	Prikaži verziju firmvera
`defaults`	Vrati sve postavke na zadane
`save`	Spremite postavke i ponovno pokrenite
`exit`	Izlaz CLI (ponovno pokretanje bez spremanja)
`diff`	Prikaži promijenjene postavke (korisno za dijeljenje konfiguracija)
`dump`	Prikaži sve postavke
`dump all`	Prikaži sve postavke uključujući hardverske zadane

Essential Settings

Značajke ploče &a

``` # List available features feature list

Enable/disable features

feature GPS feature TELEMETRY feature LED_STRIP

Set mixer type

mixer = ORNITHOPTER ```

Prijemnik

set serialrx_provider = CRSF set serialrx_inverted = OFF set serialrx_halfduplex = OFF set rssi_channel = 0

Baterija

set vbat_min_cell_voltage = 330 set vbat_max_cell_voltage = 430 set vbat_warning_cell_voltage = 350

Servosi

set servo_pwm_rate = 330 set servo_center_pulse = 1500 set flap_spread = 20

ONDAS Postavke (apiVerzija 1.46+)

``` # Cadence — timing modulation set ondas_cadence_gain = 50 # 0-100, timing brain set ondas_cadence_phase = 0 # -180° to +180°

Ferocity — asymmetric thrust

set ondas_ferocity_p_gain = 40 # Immediate thrust asymmetry set ondas_ferocity_d_gain = 30 # Anticipatory drag exploitation set ondas_ferocity_roll_gain = 50 # Roll-axis ferocity scaling set ondas_ferocity_yaw_gain = 40 # Yaw-axis ferocity scaling

Balance — wing symmetry

set ondas_balance_gain = 50 # Left/right wing balance

Advanced

set ondas_warp_gain = 0 # Stroke waveform warping set ondas_warp_yaw_gain = 0 # Yaw-specific warping set ondas_anchor_gain = 0 # Phase anchoring strength set ondas_resonance_gain = 0 # Airframe resonance compensation ```

Profili leta

``` # Switch between profiles profile 0 # Profile 1 (default) profile 1 # Profile 2 profile 2 # Profile 3

Profile-aware settings use index:

set ondas_cadence_gain = 50 # Current profile only ```

Servo montažni kut (apiVerzija 1.46+)

set servo_mount_angle_0 = 0 # Wing servo 0 mounting offset (±30°) set servo_mount_angle_1 = 0 # Wing servo 1 mounting offset (±30°) set servo_mount_angle_2 = 0 set servo_mount_angle_3 = 0

Postavke stope

``` set roll_rc_rate = 90 set roll_srate = 65 set roll_expo = 30

set pitch_rc_rate = 90 set pitch_srate = 65 set pitch_expo = 30

set yaw_rc_rate = 90 set yaw_srate = 50 set yaw_expo = 20 ```

Sigurno

set failsafe_delay = 4 set failsafe_procedure = LAND set failsafe_throttle = 1000

Dijeljenje vaše konfiguracije

Koristite diff za izvoz samo postavki koje nisu zadane:

``` # In CLI: diff

Copy the output — this is your complete configuration

# To restore, paste the diff output into CLI and type ‘save’ ```